POLISHING SAMPLES ON THE LOGITECH WG2: USER GUIDE
|
|
Author: | E. Fisher |
Reviewer(s): |
|
Editor(s): | S. Boehm, S. Frank |
Management Approval (Name, Title, Date): | B. Mills (Lab Officer) |
Audience: | Technicians |
Origination date: | 5/1/2013 |
Current version: | 7/30/2018 |
Revised: |
|
Domain: | Thin Section Lab |
System: | Logitech WG2 |
Keywords: | Polishing Samples |
...
TRODUCTION
This user guide will help thin section technicians polish their samples to the target thickness of 30 microns. This is the final stage in the thin section process. For more information refer to the Logitech Thin Rock Section Production manual, available in the Thin Section Lab both on a Logitech thumb drive in the bookcase and computer under the "Manual" folder on the desktop. Or, refer to Operation and Maintenance of the LP50 Lapping and Polishing Machine manual, located in the black binder in the Thin Section Lab bookcase labeled "LP50, PM5 and Associated Equipment".
PROCEDURE
LOGITECH WG2 SET UP
- Press the Main button under the joystick.
- Press the middle of the joystick for ok (Fig. 1).
Figure 1
3. Checking system (Fig. 2) screen will appear. Press ok to continue.
Figure 2
4. Process Screen and Machine Setup (Fig. 3) will appear.
Figure 3
5. Select Process Screen and press ok.
...
6. On the Confirm Action (Fig. 4) screen move the joystick down and press Ok.
Figure 4
7. Press ok on the Please Set Position (Fig. 5) screen.
Figure 5
8. The Operations (Fig. 6) screen will appear.
Figure 6
9. Place the abrasive drum (Fig. 7) on the top of the WG2.
...
Figure 7
a. Lift the polishing plate and pull it out from under the WG2.
...
e. Line up the edges of the polishing pad and polishing plate. Press the pad down by sweeping your hand back and forth across it to prevent from bubbles forming under it (Fig. 8).
Figure 8
f. Slowly, remove the backing and continue sweeping your hand.
g. Fold the backing in quarters with the smooth side on the outside. Press on it and move it around the pad. This will help secure the pad and remove any bubbles (Fig. 9).
Figure 9
h. Replace the polishing plate and lower the WG2.
POLISHING SAMPLES
- Wet the polishing pad by spraying it down with ethane dial.
- Spray a small amount of ethane dial on the slide holders and place the samples frosted side up onto the holders (Fig. 10).
Figure 10
3. Place sample face down on the polishing pad under a carousel post (Fig. 11).
4. Lower the post down by rotating it counter clockwise and gently setting it down in the middle hole of the slide holder (Fig. 11).
Figure 11
- If all six carousel posts need to be used it can be rotated around by moving the joystick to the left on the Operations screen and selecting WG2 (Fig. 6).
Figure 12
- While on the WG2 (Fig. 12) screen, select Wg2 and change it from "off" to "on".
- Then select the Wg2 Rate and increase it to 70%.
- On the WG2 (Fig. 12) screen move the joystick down to Override and change it from an "X" to a "Check" just until it rotates the carousel enough so you can access the other side. Then change override back to an "X".
...
- Change Abrasive from "off" to "on" (Fig. 13).
- Select Override and change it from an "X" to a "Check". The drum will begin to turn.
Figure 13
c. Start the slurry dripping on the polishing plate by spraying ethane diol into the drip tray.
...
20. Before leaving at the end of shift make sure the scoop in the abrasive drum is out of the slurry.
GETTING THE RIGHT THICKNESS AND POLISH
- Target thickness is 30 microns.
- Keep in mind; it is always better to have it too thick than too thin. Materials can always be taken away but never added.
- If samples are polishing down fast:
- Use less weight and shorter time.
- If samples are polishing down slow:
- Use more weight, longer time, and increase the "Speed" of the WG2
- If the sample becomes wedged (thicker on one side than the other) hold it on the polisher by hand.
- Hold the thinner side of the sample with your left hand.
- Place the thick side of the sample on the edge of the polishing pad while other samples are running.
- Use one or two figures on your right hand to apply pressure to the sample.
- While holding the sample on the polisher move it in a circular motion.
- Measure it every 8 to 4 minutes.
- Do not only use the micrometer to determine thickness.
- Place the sample under the microscope and turn on the transmitted light. Look for an "identifying" mineral such as, quartz or plagioclase.
- If the sample is too thick these minerals will turn from black to yellow when rotated.
- If the samples are just right they will turn from black to a very light yellow.
- If the sample is too thin they will turn from black to clear.
- Place the sample under the microscope and turn on the transmitted light. Look for an "identifying" mineral such as, quartz or plagioclase.
- Determine how polished the sample is.
- Place the sample under the microscope and turn on the reflected light.
- The minerals should look "clear" not "grainy"
- Some soft samples will not polish well no matter what.
- Place the sample under the microscope and turn on the reflected light.